Description

Introduction

This Australian Standards approved immobiliser alarm provides two circuits of engine immobilisation operated by rolling code random encrypted remote control. Entry point protection of doors, boot and bonnet with an intelligent glass break sensor. Audible warning is achieved via a standard 115dB siren, visually via the vehicle indicators and via a dash mounted high intensity red LED. The system may provide keyless entry

  • Proudly Australian
    Designed and engineered in Perth, Western Australia
Operation
  • Arming procedure while ignition is off
    The system will arm immediately if the main button of a valid remote control is momentarily pressed,  and all security functions will become active
  • Disarming procedure
    The system will disarm when the main button of a valid remote control is pressed
  • Auto Arming
    The car’s engine is automatically immobilised 40 seconds after the engine has stopped. The auto-arming feature is disabled while the system is disarmed and the ignition switch is in the ON position
Immobilisation
  • Dual Immobilisation Circuits
    The system features two independent 30 Amp rated, normally open immobilisation circuits, which break engine critical signals in the vehicle. Starter motor, fuel pump, fuel injection, main ignition are commonly immobilised circuits
  • Safety circuitry in case of power failure
    System sources alternate power from ignition if main power is lost
  • Component protection against harsh road conditions
    All relays are fully encapsulated to provide protection against dust and moisture
Controllers
  • Rolling Code / Code Hopping
    Rolling code encoder with over 18,000,000,000,000,000,000+ code combinations, transmitting via 433MHz PWM RF signal
  • Controller Type
    Uses two black ABS plastic remote controls with long life Lithium batteries
  • Large system memory
    Allows system to track three controllers
  • Compatible Remotes
    This system comes standard with REM-111
  • Remote battery life
    Two CR2016 Lithium batteries have a expected average life span of between 9 and 18 months (depending on usage).
Wiring
  • Security wiring
    All cables extending from the control module are black and same diameter. Identifying wire tags are removed by the installer during installation of the system
  • Plug and play for service
    Designed to allow easy access for service technicians. Plugs and sockets are located inside the main control module to protect against access by thieves
  • Security housing
    Connector plug is enclosed within module case to prevent access by thief
  • Stealth wiring
    Cutting any immobilisation wiring will still leave the car secure. Bypassing security is not possible by simply removing the system from the vehicle
Override
  • Emergency Personal Identification Number (PIN) override
    If the valid controller are lost, stolen or broken, the user by over-ride the system by enter the secret four digits via the ignition switch
  • Alterable PIN
    A factory programmed PIN comes standard with each system. It is recommended the owner of the system changes the PIN to a new, easily remembered number
  • One shot override
    Immobiliser always re-arms to protect vehicle. Re-enter PIN if vehicle needs to be driven after auto-arming has occurred
  • PIN card
    A record of the factory programmed override PIN is supplied on handy wallet sized card
Visual Output
  • Super bright red dash LED
    This LED flashes to inform user when system is armed. The LED is mounted on the driver’s side dash and is visible from outside the window
  • Arm/Disarm confirmation
    System flashes car indicators when arming or disarming
  • Alarm illumination
    System flashes car indicators when thief triggers alarm
Audio Output
  • Standard siren
    AS/NZS 3749.1:2003 Class B approved 115dB siren
  • Negative siren output
    Can be used to trigger car horn relay or siren
  • Arm/Disarm confirmation
    System sounds a siren when arming and disarming
  • Temporary arm/disarm chirp disable
    Momentarily press the second button of the remote control before pressing the main button, the siren will not chirp during that one operation
Intrusion Detection
  • Doors, bonnet and boot monitoring
    Triggers alarm system if intruder opens any protected entry point in vehicle May require additional hardware or connections.
  • Audio glass breakage detection
    Uses the sound of the breaking glass to trigger (not vibration) 
  • Accepts plug-in Ultra-sonic sensor
    Sensor produces a 40KHz sound wave and measures echo to detect intruder
  • Accepts plug-in single zone microwave sensor
    Sensor produces a microwave field to detect intruder
  • Accepts plug-in dual zone microwave sensor
    Sensor produces two microwave fields, exterior field to sound siren as warning, interior to trigger alarm in full
  • Accepts plug-in single stage shock sensor
    Sensor measures vibration subjected to vehicle to detect intruder
  • Accepts plug-in two stage shock sensor
    Sensor measures two levels of shock, soft shock to sound siren as warning, heavy shock to trigger alarm in full
  • Compatible with tilt sensor
    Sensor measures vehicle angle with respect to earth, triggers if angle changes – no response to vibration
Central Locking
  • Locks and unlocks all doors
    System can trigger factory central locking, aftermarket central locking or central locking relays
  • Variable pulse time
    Extend pulse length to drive pneumatic central locking systems
  • Automatic re-locking
    System will re-arm and re-lock doors if previously disarmed by remote control and doors remain closed 
  • Anti-hijacking protection
    System locks doors when ignition is turned on, unlocks when ignition is turned off 
  • Dual stage unlock
    Allows user to unlock driver’s door before unlocking all other doors
Specifications
  • Current draw
    <10mA average while armed
    <250mA disarm (and for no more than 39 seconds after ignition is switched off)
  • Wide Operating voltage
    Operating voltage +9VDC to +15VDC
  • Operating temperature
    -20 degrees to +85 degrees for equipment designed to be installed within vehicle cabin
  • Operating temperature
    -20 degrees to +105 degrees for equipment designed to be installed inside engine compartment
  • Polarity protection
    The system circuitry is design to protect itself against accidental battery polarity reversal. This can happen when replacing the vehicle battery
  • Independent indicator power fuse
    System uses independent fuse to power indicators, ensures short circuit in indicator circuit does not affect system operation
  • Short circuit protection
    The power supply wire to the system is protected against an internal fault within the system
Convenience Functions
  • Panic / Car Finder
    Press and hold second button of remote control to cause siren to sound and indicators to flash
  • Electric window closer
    Provides signals used by electric window closers, system will close all electric windows when armed by remote control
  • Courtesy light switch activation
    System switches courtesy light on for 30 seconds or until ignition switch is turned on, when disarmed 
  • Electronic boot release
    Press and hold the secondary remote control button, while system is disarmed, to activate boot release output. The indicators will flash four time each time the boot release signal is sent
Printed Material
  • Installation Guide
    Complete installation guide and specifications
  • User Guide
    Informs the end-user of the system’s functions, features and limitations.
Warranty
  • Manufacturers warranty on Control module
    Guarantees control module is free from manufacturing defects for 24 months from time of purchase
  • Manufacturers warranty on Sundry items
    Guarantees remote controls, siren and sundry items are free from manufacturing defects for 12 months from time of purchase
Standards Compliance
  • Australian Standard for vehicle Immobilisers
    AS/NZS 4601:1999 – Australian Standards website.
  • Australian Standard for Intruder alarm systems – Road vehicles – Performance requirements
    AS/NZS 3749.1:2003 Class B – Australian Standards website.
  • Manufactured in ISO9001 facility
    Built within world standard production facility
  • AS/NZS 4601 sundry standards of compliance (or parts thereof)
    AS1939 – Degrees of protection provided by enclosures for electrical equipment (IP Codes)
    AS3300 – Approval and test specification – General requirements for household and similar electrical appliances
    AS/NZS3548 Limits and methods of measurement of radio disturbance characteristics of information technology equipment
    AS/NZS3749 – Intruder alarm systems – Road vehicles
    AS/NZS4268 – Radio equipment and systems – Short range devices
    AS/NZS61000 – Electromagnetic compatibility (EMC)
    NZS6300 – Approval and test specification – General requirements for household and similar electrical appliances
    ISO7637 – Road vehicles – Electrical disturbance by conduction and coupling
    IEC61000 – Electromagnetic compatibility (EMC)
    ASTM B117 – Standard practice for operating salt spray (fog) apparatus

Additional information

Weight 1 kg
Dimensions 20 × 18 × 10 cm

Reviews

There are no reviews yet.


Only logged in customers who have purchased this product may leave a review.